kappa series
50.5cs,60.5cs,
65.5cs
instructions
Thank you
for purchasing Infinity’s Kappa Series
automotive loudspeaker components. We’ve organized this manual
to make your installation as simple and trouble-free as possible.
Please read it thoroughly before proceeding. Remember to keep
your sales receipt with this manual in a safe place so both are
available for future reference.
INSTALLATION
CONNECTIONS
Figure 6. Mounting the tweeter using the
I-Mount™ surface-mounting kit.
Figure 5A. Mounting the tweeter using the
I-Mount flush-mounting kit.
Open the crossover housing by placing your
fingers between the terminals and the top cover,
and gently pulling off the cover. Using screws or
a wire tie, mount the crossover through the holes
provided. Observing proper polarity, connect the
speakers and amplifier as shown in 7A and 7B.
Replace the cover when you are finished making
connections and adjustments.
Infinity Kappa component crossovers include a
“Custom Contour™” adjustment. Custom Contour,
if enabled, will reduce the midrange output from
the system, resulting in more perceived bass and
high frequency.You may choose the setting that
best suits your listening perference.The default
position is “Flat”.
™
blk
–
+
–
blk
red
red
+
1
Figure 7C. Enable Custom Contour by moving the
jumper (located in the upper-left corner, inside the
crossover housing) to connect the two left pins.
Defeat Custom Contour by moving the jumper to
connect the two right pins.
1) push in
2
Figure 7A. Wiring connections on the crossover
network (shown with cover on).
2
)
turn
Contour
Contour
Figure 5B. Aiming the tweeter at a desired
listening position.
Flat
Flat
Flat
Contour
3
ROTATE TO AIM
ANGLED TWEETER
TOWARD LISTENER.
Red
To AMPLIFIER
To TWEETER
SPEAKER OUTPUTS
To WOOFER
Blk
1
SLIDE SCREW UP OR
DOWN TO ADJUST
TWEETER ANGLE.
Figure 7B. Locating wiring connections on the
50.5cs woofer. Other woofers are wired similarly.
2
TIGHTEN NUT AND
WASHER TO LOCK
ANGLE SETTINGS.
4
SECURELY TIGHTEN
THE LARGE HAND NUT.
Big Lug =
Small Lug =
- 3 -
SPECIFICATIONS
50.5cs
Type:
Crossover Frequency:
Woofer
60.5cs
Type:
Crossover Frequency:
Woofer
65.5cs
Type:
Crossover Frequency:
Woofer
5-1⁄4" 2-Way Component
3.5kHz
6-1⁄2" 2-Way Component
3.5kHz
165mm 2-Way Component
3.5kHz
Speaker Impedance:
Power Handling:
Sensitivity:
4 ohms
85W RMS, 255W Peak
90dB @ 2.83V, 1m
Speaker Impedance:
Power Handling:
Sensitivity:
4 ohms
90W RMS, 270W Peak
90dB @ 2.83V, 1m
Speaker Impedance:
Power Handling:
Sensitivity:
4 ohms
90W RMS, 270W Peak
90dB @ 2.83V, 1m
Frequency Response: 55Hz – 21kHz
Frequency Response: 45Hz – 21kHz
Frequency Response: 45Hz – 21kHz
Mounting Depth:
Cut-Out Diameter:
Tweeter
Speaker Impedance:
Power Handling:
Sensitivity:
2-1/16" (53mm)
4-11/16" (120mm)
Mounting Depth:
Cut-Out Diameter:
Tweeter
Speaker Impedance:
Power Handling:
Sensitivity:
2-3⁄16" (56mm)
5" (127mm)
Mounting Depth:
Cut-Out Diameter:
Tweeter
Speaker Impedance:
Power Handling:
Sensitivity:
2-7/16" (62mm)
5-1⁄2" (140mm)
4 ohms
50W RMS, 150W Peak
90dB @ 2.83V, 1m
4 ohms
50W RMS, 150W Peak
90dB @ 2.83V, 1m
4 ohms
50W RMS, 150W Peak
90dB @ 2.83V, 1m
Frequency Response: 3.5kHz – 21kHz
Mounting Depth:
Cut-Out Diameter:
1-3⁄16" (31mm)
1-3/4" (45mm)
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility, that the products
described in this owner’s manual are in compliance
with technical standards:
EN 50081-1:1992
EN 50082-1:1997
Infinity Systems, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
© 2002 Infinity Systems, Inc. • P/N: KAPCSOM1/02 • Printed 1/02
Vincent Delanoe
Harman Consumer International
Chateau-du-Loir, France. 1/02
|